Converter

The IOP760 CR is a wireless converter for machine-to-machine links. It moves data between Wi-Fi, Ethernet and a serial UART port, so serial or Ethernet devices can be reached over a wireless network. Serial data can be sent transparently or wrapped in Modbus protocol.The Wi-Fi side supports IEEE 802.11a/b/g/n/ac and dual-band 2.4/5 GHz operation, and can run as a Wi-Fi uplink or as a multi-mode access point. If the signal drops below a set threshold, the unit can roam to a stronger access point. Two LAN ports allow local Ethernet devices to share the same link, and a single RS-232/485 port with RJ12 connector covers serial devices, with a 1-channel digital input and a 1-channel relay output for triggering or event reporting.The metal housing mounts on a DIN rail or bracket and operates from +9~ 48 VDC. The source lists this ordering code as Asia-only and notes that it will be phased out.ApplicationsWireless machine-to-machine (M2M) communicationWireless connection of Modbus RTU serial devicesConnecting local Ethernet devices over a Wi-Fi linkDevice triggering and event reporting via digital input and relay output

The IOP760AM CR moves data between Wi-Fi, Ethernet and a serial UART port, so a Modbus RTU device or a local Ethernet device can be reached over a wireless link without running cable between them. The Wi-Fi side covers IEEE 802.11a/b/g/n/ac and can act as an uplink or as a WAN connection, depending on how the unit is set up.For sites with changing radio conditions, the unit can switch to a stronger access point through its roaming function once the signal drops below a configured threshold. Serial data can be passed through directly or framed using the Modbus protocol, and the single RJ45 LAN port lets local Ethernet devices share the same connection.A wet-contact digital input and a relay output allow simple event reporting and device triggering. The metal body is designed for DIN-rail or bracket mounting, with a 9 to 48 VDC power input and an operating range of -20 ~ 60 °C.ApplicationsWireless connection of Modbus RTU serial devicesLinking local Ethernet devices over a Wi-Fi uplinkEvent reporting and device triggering via digital input and relay output

The IOP760AM-EU CR is a wireless converter that exchanges data between three interfaces: Wi-Fi, Ethernet and UART. Wi-Fi can serve as the uplink, or the unit can use an Ethernet WAN connection instead, while a local Ethernet switch can link further Ethernet devices through the unit.Serial data can be sent directly over the RS-232/485 port or formatted using the Modbus protocol, which suits engineers connecting Modbus RTU devices to a wireless network. Users can choose IEEE 802.11 b/g/n for 2.4 GHz or IEEE 802.11 ac for 5 GHz. When the signal drops below a set threshold, the roaming function can move the unit to a stronger access point.A digital input and a relay output allow the unit to be used for device triggering or event reporting. The solid metal body can be fitted to DIN-rail or bracket mounting kits, and the unit is rated for an operating temperature of -20 ℃ ~ 60 ℃. This variant is supplied with a category E plug type.ApplicationsWireless connection of serial Modbus RTU devices to Ethernet or Wi-Fi networksDevice triggering and event reporting over a wireless link

MB TCP/RTU Data-Exchange With Wi-Fi Interface Gateway (Asia Only).

The WF-2572 CR bridges a wired Ethernet device onto a Wi-Fi network, allowing an industrial device with an RJ-45 port to communicate wirelessly without complex configuration. Ethernet-to-Wi-Fi conversion uses transparent transmission, so the connected equipment does not need to be aware of the wireless link.The unit supports dual-band operation on 2.4 GHz and 5 GHz. Because the 2.4 GHz band is more crowded, the 5 GHz band typically sees less interference, which can help in environments with many wireless devices. Limit-AP and Infrastructure modes are available, with WPA-PSK and WPA2-PSK encryption.Setup is handled over USB, and no driver installation is required. The bridge is suited to cabinet mounting on DIN-rail with an extended operating range of -25 °C to +75 °C. The manufacturer lists this ordering code as Asia Only, so confirm regional suitability before ordering.ApplicationsWireless connection of Ethernet-based industrial devicesRetrofitting wireless links into existing wired automation installationsCabinet-mounted wireless bridging in environments with a wide temperature range

WF-2572M Ethernet to Wi-Fi Bridge with metal case. (Asia Only).