Medieconvertere

The NS-200AFC-T CR converts a 10/100 Base-TX copper Ethernet connection into a 100 Base-FX multi-mode fibre link, with one RJ-45 port on the copper side and one SC connector on the fibre side. It suits industrial Ethernet runs that need a copper-to-fibre transition inside a control cabinet or along a plant network.On the Ethernet side the converter negotiates 10/100 Mbps speed automatically and switches between MDI and MDI-X automatically, so straight or crossover cables can be used without configuration. It uses store-and-forward switching, supports IEEE 802.3x flow control and includes reverse polarity protection on its power input. The fibre port is specified for 2 km over multi-mode fibre, with 62.5/125 μm recommended for full duplex operation.The housing is plastic with DIN-rail mounting and measures 33 x 107 x 78 mm (W x L x H). It is rated for operation from -30 °C to +75 °C and storage from -30 °C to +85 °C, at 10% to 90% RH non-condensing. The power input accepts +12 to +48 VDC and is non-isolated.ApplicationsExtending industrial Ethernet links from copper to multi-mode fibreConnecting copper-based devices to a fibre backbone in control cabinets and plant networks

NS-200AFCS-60T is an industrial media converter that bridges a copper 10/100Base-TX Ethernet segment and a 100Base-FX single-mode fibre link with an SC connector, rated for 60 km. It suits engineers who need to extend an Ethernet connection over a long fibre run without changing the connected equipment.The RJ-45 port negotiates 10 or 100 Mbps automatically and detects MDI/MDI-X wiring itself, so it can be installed without crossover cables. The store-and-forward design handles traffic between the two media, and reverse polarity protection guards the power input.The unit accepts a wide +12 to +48 VDC supply and runs from -30 to +75 °C. Its slim plastic housing mounts on a DIN rail, and the status LEDs show power, speed, link activity and fibre duplex mode.ApplicationsExtending industrial Ethernet links over single-mode fibre up to 60 kmConnecting RJ-45 equipment to a fibre backbone in DIN-rail mounted control panels

NS-200AFCS-T bridges a copper Ethernet segment and a single-mode fibre link, letting engineers extend industrial Ethernet networks over distances of up to 30 km. The RJ-45 port handles 10/100 Mbps with auto negotiation and automatic MDI/MDI-X, so it can be connected without concern for cable wiring or port polarity.The converter uses a store-and-forward architecture with 1024 MAC table entries and IEEE 802.3x flow control. The fibre side uses an SC connector and supports 8.3/125, 8.7/125, 9/125 or 10/125 μm single-mode cable at a wavelength of 1300 or 1310 nm.Built for control cabinets, it has a plastic housing and a slim profile for DIN-rail mounting. It operates from -30 ~ +75 °C and accepts +12 ~ +48 VDC with reverse polarity protection. The ordering code NS-200AFCS-T CR is the RoHS-compliant version.ApplicationsExtending industrial Ethernet links over single-mode fibreConnecting remote Ethernet devices to a fibre backbone in control cabinets

NS-200AFT-T bridges a copper Ethernet segment and a multi-mode fibre link. The RJ-45 port runs at 10 or 100 Mbps with auto negotiation and automatic MDI/MDI-X, so it can be connected to a switch or a device without choosing a crossover cable. The fibre side uses a 100Base-FX multi-mode ST connector, suited to extending an Ethernet connection across the distances covered by the fibre specification.The converter uses store-and-forward processing with wire-speed switching and supports IEEE 802.3, 802.3u and 802.3x, including flow control. Reverse polarity protection is fitted on the power input, which accepts +12 VDC to +48 VDC (non-isolated). Power consumption is 0.12 A at 24 VDC.The plastic housing is slim enough for DIN-rail mounting and is rated for an operating temperature of -30 °C ~ +75 °C, with a storage range of -30 °C ~ +85 °C. Status LEDs show power, 10M and 100M speed, link/activity and the fibre duplex state. The product is listed with CE, UKCA, FCC, RoHS and WEEE certifications.ApplicationsExtending 10/100Base-TX Ethernet connections over 100Base-FX multi-mode fibre in industrial installationsConnecting copper-based Ethernet devices to a fibre backbone in cabinets with a DIN-rail footprint

NS-200WDM-A is the local-end unit of a single-strand fibre media converter pair. It bridges a 10/100Base-TX RJ-45 Ethernet port to a 100Base-FX SC fibre link, carrying both transmit and receive traffic over one single-mode fibre using wavelength division multiplexing (TX 1310 nm, RX 1550 nm). This halves the number of fibres needed for a link, which is useful where long-distance fibre is costly to install.The unit is designed for plug-and-play use, with automatic MDI/MDI-X crossover and 10/100 Mbps auto negotiation. It uses store-and-forward switching and provides 1500 Vrms isolation. Overload protection, soft start, high/low voltage protection and reverse polarity protection are included. Its 32.3 mm width suits compact DIN-rail installations.Important: this unit works as a pair. You must order NS-200WDM-A together with NS-200WDM-B at the other end of the link.ApplicationsExtending 100 Mbps Ethernet over long-distance single-mode fibreReducing fibre infrastructure cost by reusing a single strandSpace-constrained control cabinets and DIN-rail installations

The NS-200WDM-B is a single-strand fibre media converter that carries Ethernet over one single-mode fibre instead of two. Wavelength division multiplexing sends two independent data channels along the same strand, with this unit transmitting at 1550 nm and receiving at 1310 nm. It is well suited to extending Ethernet links over longer distances where fibre installation is costly.The NS-200WDM-B works only as a pair with the NS-200WDM-A, which must be installed at the opposite end of the link. The unit uses store-and-forward switching, automatic MDI/MDI-X crossover and IEEE 802.3x full duplex flow control, so it can be connected without special cabling. A soft start function, overload protection and high-low voltage protection are included, and a reverse polarity protected +12 ~ +48 VDC supply simplifies installation on DIN-rail equipment racks.Ordering code NS-200WDM-B CR is the TX 1550 nm / RX 1310 nm side of the series. Specify the matching NS-200WDM-A when ordering to ensure both ends of the link are compatible.ApplicationsExtending Ethernet connections over long single-mode fibre linksReducing fibre infrastructure cost by running two channels over one strandConnecting remote Ethernet devices to a network across a fibre backbone

The NSM-200G-SFP links a 10/100/1000Base-T copper Ethernet segment to a 1000 Mbps fibre link through a single SFP slot. It suits engineers who need to extend an existing network, bring non-fibre equipment onto a fibre backbone, or stretch the distance between two devices without changing the rest of the installation.The SFP slot accepts a 1000 Base-LX device, and the converter is transparent to jumbo packets up to 10 KB. Link Fault Pass-through (LFP) is available and is enabled through the DIP switch, so a fault on one side of the link can be relayed to the other side. Store-and-forward processing and 512 Kbit of frame buffer memory are provided.The metal housing is designed for DIN-rail or optional wall mounting. The unit accepts redundant +12 VDC ~ +48 VDC power input with reverse polarity protection, and includes a relay alarm output rated 1 A @ 30 VDC. Operating range is -30 °C ~ +75 °C.ApplicationsExtending the distance of an existing Ethernet networkConnecting non-fibre equipment to a fibre linkExtending the distance between two devicesIndustrial Ethernet installations requiring link fault pass-through

The NSM-200LX CR is an industrial media converter that transparently links a 10/100/1000Base-T copper Ethernet connection to a single-mode fibre link. Its SC port operates at 1310 nm with a rated distance of 10 km, making it a practical way to extend an existing network or the separation between two devices.It suits harsh-environment installations, with an operating range of -30 °C ~ +75 °C and redundant +12 VDC ~ +48 VDC power inputs, so a backup supply can keep the link running. Link Fault Pass-through (LFP) can be enabled by DIP switch, allowing a fault on one side of the link to be signalled to the other.Key handling characteristics include store and forward processing, IEEE 802.3x flow control, Energy Efficient Ethernet (802.3az) and transparency to jumbo packets up to 10 KB. The metal housing mounts on a DIN-rail or, optionally, on a wall.ApplicationsExtending the reach of existing Gigabit Ethernet networks over single-mode fibreLinking two devices separated by up to 10 kmConverting copper Ethernet equipment to fibre connectivity in industrial installations

The NSM-200SX CR converts 1000Base-T copper Ethernet into 1000Base-SX multi-mode fibre, letting engineers extend a network segment or bridge a copper device onto a fibre backbone without changing the surrounding equipment. It offers a single RJ-45 port and a single SC fibre port, with Store & forward processing and IEEE 802.3 Ethernet, flow control and energy-efficient operation support.Link Fault Pass-through (LFP) can be enabled with a DIP switch, so a fault on one side of the link is reflected to the other side. This helps the connected devices detect link loss quickly. The alarm relay output and dual redundant +12 VDC ~ +48 VDC power inputs with reverse polarity protection add resilience to panel installations.The metal housing is suited to DIN-rail mounting, with wall mounting as an option, and the unit is rated for an operating range of -30 °C ~ +75 °C. Choose this variant when you need a multi-mode 850 nm link of up to 0.55 km with SC connectors.ApplicationsExtending the distance of an existing Ethernet networkConnecting copper-only equipment to a fibre networkExtending the distance between two devices over multi-mode fibre

NSM-200SX2 converts a 10/100/1000Base-T copper Ethernet connection into a 1000Base-SX multi-mode fibre link, letting engineers extend an existing network or connect a copper-only device to fibre without changing the rest of the installation. The single SC port uses 50/125 μm multi-mode fibre at 1310 nm with a rated distance of 2 km.The unit suits industrial cabinets where reliability matters. It offers store-and-forward processing, transparency to jumbo frames, and Link Fault Pass-through (LFP), which can be enabled by DIP switch so that a fault on one side of the link is reflected to the other. Redundant +12 VDC ~ +48 VDC power inputs, a relay alarm output and a metal casing complete the specification, with DIN-rail or optional wall mounting.Choose the NSM-200SX2 CR when you need a 1000Base-SX multi-mode solution with an extended operating range from -30 °C to +75 °C. Related models in the series include the NSM-200SX, NSM-200LX and NSM-200G-SFP.ApplicationsExtending the reach of an existing copper Gigabit Ethernet network over multi-mode fibreConnecting a 1000Base-T device to a 1000Base-SX fibre linkExtending the distance between two Gigabit Ethernet devicesLinking non-fibre equipment to a fibre backbone in industrial installations